This Limestone tiled floor was installed at a property in Fulham, I was asked round to quote for cleaning the floor and whilst I was there I did a patch test. The test worked very well and the owner couldn’t believe that the grout was actually white not dark grey.
Cleaning Polished Limestone Floor Tiles
The first step was to give the floor a quick sweep to remove any surface grit etc. Before starting the burnishing process which we use on hard stone surfaces such as polished Limestone to clean and bring up the shine on the floor. The burnishing pads and encrusted with diamonds and come in a pack of four consisting of Coarse, Medium, Fine and Very Fine 17” pads. I started with a coarse pad which removes sealers and dirt from the floor, a little water is added to lubricate the process.
Once we had finished with the coarse pad the grout was cleaned up using Tile Doctor Pro-Clean diluted 1 part cleaner to 4 parts water. The solution was then scrubbed into the grout with a stiff hand brush until it was clean. The floor was then rinsed with clean water to remove any cleaning products and we then continued with the remaining burnishing pads applied in order with Medium, Fine and Very Fine until the floor was thoroughly cleaned and polished. We left for the day at this point to allow the tiles to dry overnight.
Sealing Limestone Floor Tiles
The following day we returned to seal the floor using two coats of Tile Doctor Colour Grow which is a great sealer for natural stone such as Limestone as it works to lift the colours out of the stone. The last step was to buff the floor to a nice shine with a rotary machine fitted with a white polishing pad.
The customer was really pleased with the result and couldn’t believe that the floor could look so good.
Limestone Floor, Cleaned, Scrubbed, Polished and Sealed in Fulham
I had an inquiry from a client in Fulham, who was representing the residents of an old building. The building had recently undergone redecoration and in the hallway, they had removed a thirty year old carpet to discover an original encaustic tiled floor underneath which turned out to be 102 years old.
As you can see from the photographs the floor was extremely dirty and covered in lots of glue and paint from the carpet and decorations. Naturally they were keen to have it restored and brought back to life. Given the condition of the tile and the age I to set their expectations and told them that although I was confident of making a big difference to the floor I couldn’t give any guarantees. I gave them my quotation and although it was slighter higher than what they had I mind, it was still less than other quotations that they had received and were also considering the option of replacing the carpet.
After a couple of days I received a call asking me to go ahead with the work and I booked it in.
I left this to dwell on the tile for about fifteen minutes before scrubbing it in using a black scrubbing pad on my rotary machine. This approach removed some glue and a lot of old grime so I then sprayed down more Remove and Go and also used a steamer to loosen the remaining glue and paint. This process was repeated a section at a time until at the end of the day I gave the whole are a thorough rinse before packing away my equipment and leaving it to dry.
Encaustic Tiled Floor Sealing
I returned three days later and carried out a test with my moisture meter to make sure that the floor was dry enough to seal. The meter confirmed it was dry so I then sealed the floor using two coats of Tile Doctor Colour Grow which is an impregnating sealer that really brings out the colour in the tiles.
And as you can see the floor is transformed and now I have some happy residents who are really pleased that they opted to have the old floor cleaned instead of replacing the carpet. Not to mention that restoring such an original feature has probably added value to their investment as well.
Original Encaustic Tiled floor cleaned and restored in Fulham
Following on from a referral from a Property Management company I paid a visit it to this palatial property in Oxshott which had approximately 300m2 of Marble tiled flooring that they wanted cleaning and re-polishing, my initial quotation to do this mechanically was too high so I offered an alternative using diamond encrusted burnishing pads which reduced the cost significantly. I didn’t receive an answer so I thought that was the end of it however five months later I got an email asking me to carry out the works.
Marble Tiled Floor Polishing
This was a very large area so we had two men working with burnishing pads in 10 metre sections. The pads come in a set of four; you start with the coarse pad together with a little water and this cuts through and removes surface grime and any surface seal. You then progress through the other finer pads one by one until you get to the final polishing pad which provides a high polish.
Fortunately there were not many stains and the ones that were there came out quite easily. When we had completed a room using this system we then applied Tile doctor Shine powder which is a crystallising power worked into the floor using a white buffing pad and a little water; it adds an extra level of deep shine to the marble floor giving it that extra wow factor together with a tough durable finish, we did this working 1 m2 at a time.
This whole process took five days to complete and when we had finished the client came to inspect it with the homeowner. She was delighted with the final finish and has said that she will be recommending us to all her friends and clients. This is also great for the property manager because it has given him a good reputation for providing a trustworthy and highly skilled contractor for the works. Also he has promised us further work from his other clients including a job to carry out the external stone cleaning works for the same client.
Cleaning and Polishing a Large Marble Tiled floor in Oxshott, Surrey
We were contacted by a builder who had recently laid Porcelain Tiles in an office reception in Wimbledon. Although he has laid this type of tile in various art galleries around London without problem, in this particular lobby which is situated next to a shopping centre the tiles were extremely slippery and the facilities manager wanted the tiles changed at the expense of the builder.
Obviously this would have been an expensive option and so the builder contacted Tile Doctor for help. Initially he had considered having a member of his team apply the treatment however he realised that as a Tile Doctor applicator we had been trained to apply the treatment properly and this gave the facilities manager confidence it would have been applied to the correct standard so we were awarded the work and asked to carry it out on a Sunday when the building would be empty.
Applying the Anti-Slip Treatment
We arrived at the agreed time and were let in by the shopping centre security team. The area we were treating was around 25m2 so decided to work in 5m2 sections first cleaning the tile using the first stage Ant Slip product worked into the tile with a rotary floor machine fitted with a polypropylene brush head and then removing with a wet vacuum followed by rinsing with clean water.
We carried on with this process until the whole floor was done and let it dry before going onto the next stage to apply the Tile Doctor Anti slip (stage two) and leaving for between 3 to 5 minutes before applying the stage three which locks in the Anti Slip.
The Anti Slip product is invisible to the eye however it’s very easy to test it’s been applied, all you need to do is wet the tile as the product only activates when it’s wet.
When we had finished the whole floor we then tested it again just to make sure that everything worked well we cleared away all the tools making sure we left the area tidy and safe and locked the building up.
The Job took us one night and the customer is now recommending us to all other sites that have had these tiles fitted.
Preventing slips and trips on Porcelain Tile in a Wimbledon Office
Set of photographs here from a Victorian Tiled floor for a customer in Balham, South London. They had found the floor under an old carpet, and wanted to restore it. Unfortunately their builders did not listen and didn’t bother to put down any protection when they painted, as a result there was paint everywhere, I’ve include a detailed photograph below so you can see for yourself what a state the floor was in.
Cleaning the Victorian Floor Tiles
Initially the floor was cleaned using a dilution of Tile Doctor Pro-Clean mixed 50:50 with NanoTech UltraClean which had been left to dwell for 20 minutes before being agitated using a rotary machine fitted with a buffing pad. I used a wet vacuum to remove the dirty cleaning solution and then realising something more powerful would be required to shift the stubborn stains and paint marks. To rectify this I applied a Tile Doctor Remove and Go which is a coatings remover and left it to dwell on the Victorian tile for forty minutes before applying plenty of elbow grease. This did the trick to remove the paint and glue etc. so I worked across the floor in sections applying the same treatment until the floor was completely clean.
Once it had all been removed I gave the whole floor a scrub with Tile Doctor Grout Clean-Up and this brightened up the colours and finally I gave the floor a very thorough rinse with clean water to remove any remaining cleaning product that might have an adverse effect on the sealer. I left the floor to dry over the weekend and returned on the following Monday to seal it, but first I carried out a couple of repairs because some of the tiles were loose so I reset them in cement.
Sealing Victorian Tiled Floor tiles
On my return I sealed the floor using two coats of Tile Doctor Colour Grow which is a penetrating sealer that provides maximum stain protection whilst bringing out the colour in the stone.
All the customer could say was AMAZING I didn’t think it was possible to get like this.
Victorian Floor Cleaned and Sealed in Balham, South London
A while ago I was asked to quote to clean up an old quarry tiled floor in a converted barn in Ashtead. Whilst I was there I carried out a test patch for the lady to show what the results would be; she had said that if she wasn’t satisfied she was going to replace the floor so she must have met her expectations as a week later we were given the go ahead to carry out the work.
Cleaning Hallway Quarry Tiles
Fortunately for us they had recently removed the old kitchen and scheduled us after to clean the quarry tiles before completing the decorating and refitting a new kitchen. We cleaned the tiles using a mixture of Tile Doctor Pro-Clean diluted 1:4 parts with water and Nanotech Ultraclean which adds tiny abrasive particles into the cleaning solution. Normally I would work this into the floor using a black scrubbing pad however the floor was very uneven so I used a medium nylon brush on my rotary machine instead, this had the added advantage of reaching into the grout as well. I should mention we thoroughly rinsed the floor as we went along using a wet vacuum to remove the soiled solution. It took two of us two days to scrub the areas that had to be done and we had a blower running to help dry out the floor.
Sealing Hallway Quarry Tiles
We returned three days later and carried out moisture test to ensure the floors were dry and ready to be sealed. The Quarry tiles were then sealed them with five coats of Tile Doctor Colour Grow which is an impregnating sealer that reaches into the pores of the tile and lifts the natural colours. The owner was extremely happy with the floor and couldn’t wait to have her new kitchen installed to see how it would look.
Last week we were asked to carry out a demonstration of our AntiSlip Treatment for a lady in Ashtead Surrey. She has white shiny Porcelain tiles laid on a patio area and when they get wet they are really slippery and dangerous and she was especially concerned about young children hurting themselves. We carried out a test patch for her and asked her to see if she could slip, not only did she try, but her gran and mother-in-law also tried and were extremely impressed. I left her with our quotation so she could discuss it with her husband. The next day I received a call asking me to go ahead and carry out the works.
Applying the Anti-Slip Solution
When applying this treatment it is vital that you follow all the guidelines and times for the different types of stone. It is a 3 stage application, the first is the primer which is mixed 4 : 1 which we scrubbed into small areas of about 6m2 at a time, when scrubbing we used a brush head on our rotary scrubbing machine which has the added advantage of cleaning the tiles.
After about 5 minutes of scrubbing using a scrubbing pad we then vacuumed it all and left the tiles to dry and because we were outside in the sun it didn’t take long to dry. The next stage is to apply the Antislip treatment and for this we used a flat mop and for these type of tiles we needed to leave it to dwell for between 3 and 5 minutes, but we had to make sure that it did not dry in.
After the dwell time the 3rd stage is to scrub in another solution of the primer, but this time it locks in the Antislip. When you are scrubbing this stage you can feel the treatment working. Once we have completed this stage we vacuum it all up then rinse the area with fresh water to remove any residues.
The complete area was around 50m2 and luckily the treatment package covered this area. In all the application took two of us around five hours to complete and after clearing our equipment away we then put all the garden furniture back in place.
We returned the next day because the customer also asked us to clean their driveway and the patio area was wet because of rain, but it was great to walk on and I did not slip at all.
The customer was really happy, because if the treatment hadn’t worked her only other option would have been to rip up the tiles and replace them at a cost of thousands and to make things even better for her, this treatment will last around 4 years before she needs to have it re-applied.
Preventing slips and trips on shiny porcelain patio tiles
This beautiful slate tiled floor installed in the kitchen and hallway of a house in Balham London; I was asked by the owner if we could restore the floor following some work that had been carried out by a builder who had failed in his attempts to remove the old seal. To instill confidence that we could complete the work we carried out a demonstration on a small test area which was enough to prove that money would not be wasted and we were booked for the job, we even agreed to clean the floor on Sunday and seal it on the Monday so it would be ready in time for visitors who were due on the Wednesday.
Cleaning slate Floor Tiles
We cleaned the floor using Tile Doctor Pro-clean which is an alkaline cleaner safe to use on natural stone such as Slate; it’s very good at removing general dirt, grime and even grease. Next step was to remove the remaining sealer using Tile doctor Remove & Go which was applied to a small area at a time. I scrubbed the product into the slate and left it on the surface for a further hour making sure not to let the area dry out which temporarily made it look really dark (see photo below). Finally I gave the floor a through rinse to make sure that no chemical remained on the stone before sealing and then left for the evening.
Sealing Slate Floor Tiles
The next day I checked the floor was dry using a moister meter which thankfully it was and then started to seal using two coats of Tile Doctor Colour Grow which is a colour enhancing sealer design to provide maximum stain protection on natural stone floors whilst bringing out the deep colour in the stone and providing a natural matt finish.
My customer was really happy with the results and left a nice testimonial on the Tile Doctor website, she has also booked me in to clean her driveway next month.
Slate Floor Cleaned, Stripped and Re-Sealed in Balham, South London